SimulationsSimulacionesSIM-0006

Simulate, 5 minutesSimular, 5 minutos

Wire a circuitConecte un circuito

Lay wires between a battery, an LED, a resistor, a switch and a gap. Make a full loop and the LED lights; leave a break anywhere and nothing flows.Ponga cables entre una pila, un LED, una resistencia, un interruptor y un hueco. Haga un circuito completo y el LED se enciende; deje una interrupción en cualquier lugar y nada fluye.

A circuit board with a coin cell in its holder, a banded resistor, a dark LED, an open knife switch and a paper clip across a gap between two copper pads, two wires laid.

The drawing shows where it starts. It runs here once its script has loaded.El dibujo muestra dónde empieza. Funciona aquí una vez que carga su código.

Your challengeSu reto

  1. Finish the loop so the LED lights.Complete el circuito para que el LED se encienda. Not done yet.Todavía no.
  2. Make it shine bright but safe: between fifteen and twenty-five milliamps through the LED.Hágalo brillar fuerte pero sin riesgo: entre quince y veinticinco miliamperios por el LED. Not done yet.Todavía no.
  3. Make one big loop through every part, the resistor, the LED, the switch and the gap, so the switch turns the light on and off.Haga un solo circuito grande que pase por todas las partes, la resistencia, el LED, el interruptor y el hueco, para que el interruptor encienda y apague la luz. Not done yet.Todavía no.

Every challenge done. Now try it for real at home.Todos los retos logrados. Ahora pruébelo de verdad en casa.

The batteryLa pila
What bridges the gapQué une el hueco

Lay a wire: pick one end, then anotherPonga un cable: elija un extremo y luego otro

BatteryPila

LEDLED

ResistorResistencia

SwitchInterruptor

The gapEl hueco

Wires laidCables puestos

    Current through the LEDCorriente que pasa por el LED

    Current out of the battery, and back into itCorriente que sale de la pila, y que regresa a ella

    Tap two ends on the board, or drag from one to another, to lay a wire; tap the switch to flip it. The dots are the moving charge and the arrows its way: out of the plus side, around the loop, back into the minus side. The bar fills at what a small LED is made for.Toque dos extremos en la tablilla, o arrastre de uno a otro, para poner un cable; toque el interruptor para moverlo. Los puntos son la carga en movimiento y las flechas su camino: sale del lado positivo, da la vuelta al circuito y regresa por el lado negativo. La barra se llena con lo que aguanta un LED pequeño.

    What is happeningQué está pasando

    Electricity flows only around a complete loop: out of the battery’s plus side, through every part, and back into its minus side. Break the loop anywhere, with an open switch or an empty gap, and it all stops.La electricidad solo fluye por un circuito completo: sale por el lado positivo de la pila, pasa por cada parte y vuelve por su lado negativo. Si el circuito se rompe en cualquier lugar, con un interruptor abierto o un hueco vacío, todo se detiene.

    Metal carries electricity and rubber does not, so a paper clip can close a gap and a rubber band cannot. An LED is a one way valve: it lights only with its long leg toward the plus side.El metal conduce la electricidad y la goma no, así que un clip puede cerrar un hueco y una liga no. Un LED es una válvula de un solo sentido: solo se enciende con su pata larga hacia el lado positivo.

    Nothing is used up in the wire: the same current that leaves the battery comes back to it, which is why the board shows the same number at both ends of the battery. What the light uses is the energy the battery supplies.Nada se gasta en el cable: la misma corriente que sale de la pila vuelve a ella, por eso la tablilla muestra el mismo número en los dos lados de la pila. Lo que usa la luz es la energía que da la pila.

    A resistor holds the current down so the LED is not pushed too hard. Two AA cells push with the same three volts as one coin cell, so through the same resistor the light is about as bright: a bigger battery lasts longer, it does not push harder.Una resistencia frena la corriente para que el LED no se fuerce demasiado. Dos pilas AA empujan con los mismos tres voltios que una pila de botón, así que con la misma resistencia la luz brilla casi igual: una pila más grande dura más, no empuja más fuerte.

    Things to tryCosas para probar

    • Lay the last wire to finish the loop, then turn the LED around. Does it still light?Ponga el último cable para completar el circuito y luego voltee el LED. ¿Todavía se enciende?
    • Run the loop through the gap and bridge it with the paper clip, then the rubber band, then nothing. Which ones are conductors?Pase el circuito por el hueco y únalo con el clip, luego con la liga, luego con nada. ¿Cuáles son conductores?
    • Take the resistor out with the two AA cells and read the warning, then find the resistor that keeps the LED bright but safe.Quite la resistencia con las dos pilas AA y lea la advertencia; luego busque la resistencia que deja el LED brillante pero sin riesgo.
    • Join the battery’s plus and minus sides with one wire and watch where the current goes. Never do this with a real battery.Una el lado positivo y el negativo de la pila con un solo cable y vea por dónde se va la corriente. Nunca lo haga con una pila de verdad.

    The numbers come from a simple model of fresh batteries, a red LED and ideal wires; real cells sag as they tire, a coin cell most of all, and LEDs differ by color and part. Real coin cells are a swallowing danger: a grown-up counts them out and back, and keeps them far from young children.Los números vienen de un modelo sencillo de pilas nuevas, un LED rojo y cables ideales; las pilas reales se debilitan al cansarse, sobre todo la de botón, y los LED varían según el color y la pieza. Las pilas de botón reales son un peligro si se tragan: una persona adulta las cuenta al sacarlas y al guardarlas, y las mantiene lejos de los niños pequeños.

    Use it, share it, adapt itÚsela, compártala, adáptela

    The credit to copyEl crédito para copiar

    Free BYRD, CC BY. “Wire a circuit” from the Byrd Academy STEM Curriculum by Byrd EDU, byrdathome.org.Free BYRD, CC BY. “Conecte un circuito”, del Currículo STEM de Byrd Academy, de Byrd EDU, byrdathome.org.

    This is free to use, share and adapt, even commercially, under the Creative Commons Attribution 4.0 International license (CC BY 4.0), with this credit. What Free BYRD means.Esto es libre de usar, compartir y adaptar, incluso con fines comerciales, bajo la licencia Creative Commons Atribución 4.0 Internacional (CC BY 4.0), con este crédito. Qué significa Free BYRD.

    Keep goingSiga adelante

    What to do nextQué hacer después

    Make it harderHágalo más difícil

    Light the LED as brightly as it can safely go with each battery, then explain which resistor you chose and why the two batteries give almost the same light.Encienda el LED con todo el brillo que puede aguantar sin riesgo con cada pila, y explique qué resistencia escogió y por qué las dos pilas dan casi la misma luz.

    For a younger onePara alguien más pequeño

    With a grown-up, lay one wire from the LED’s short leg to the battery’s minus side and watch it light, then remove that wire to turn it off.Con una persona adulta, ponga un cable de la pata corta del LED al lado negativo de la pila y véalo encenderse; luego quite ese cable para apagarlo.

    Try this nextPruebe esto después

    STEMGrades 3 to 5Grados 3 a 5 How does electricity know where to go?¿Cómo sabe la electricidad a dónde ir? STEM-ES-03

    Circuits AliveCircuitos vivos

    Discover the loop that makes a light turn on, test what conducts, and build a light-up sign with your name or a message.Descubra el circuito cerrado que enciende una luz, pruebe qué materiales conducen y construya un letrero luminoso con su nombre o un mensaje.

    • Ways in:Formas de empezar:
    • ReadLeer
    • DoHacer
    • SimulateSimular

    Grades 3 to 5Grados 3 a 5

    ManufacturingManufacturaElectronicsElectrónica

    Free BYRD, CC BYCurriculum unitUnidad del currículo

    BH-0011

    Light up a paper circuit cardIlumine una tarjeta con un circuito de papel

    Lay copper tape on a card, add an LED and a coin cell, and fold the corner to close the loop and make it light.Ponga cinta de cobre en una tarjeta, agregue un LED y una pila de botón, y doble la esquina para cerrar el circuito y encender la luz.

    • Ways in:Formas de empezar:
    • ReadLeer
    • DoHacer
    • SimulateSimular

    Best for ages 8 and upIdeal desde los 8 años

    ManufacturingManufacturaElectronicsElectrónica

    Free BYRD, CC BYHome activityActividad en casa

    BH-0035

    Be the microcontroller: run a blink program with a flashlightSea el microcontrolador: ejecute un programa de parpadeo con una linterna

    Plan a blink pattern on pseudocode cards with a delay variable, have a family member run it with a flashlight, change the variable, add a button, and tell one honest bug story.Planee un patrón de parpadeo en tarjetas de pseudocódigo con una variable de espera, pida a un familiar que lo ejecute con una linterna, cambie la variable, agregue un botón y cuente una historia honesta de un error.

    • Ways in:Formas de empezar:
    • ReadLeer
    • DoHacer
    • SimulateSimular

    Best for ages 10 and upIdeal desde los 10 años

    ElectronicsElectrónicaSoftwareSoftware

    Free BYRD, CC BYHome activityActividad en casa

    TOUR-0001

    Inside a circuit, from the wall outlet to the chipDentro de un circuito, del tomacorriente al chip

    Follow electricity from the outlet on your wall, through the wires and a phone charger, onto a circuit board and into a chip, where billions of tiny switches turn on and off.Siga la electricidad desde el tomacorriente de su pared, por los cables y un cargador de teléfono, hasta una placa de circuito y dentro de un chip, donde miles de millones de interruptores diminutos se encienden y se apagan.

    • Ways in:Formas de empezar:
    • TourRecorrer

    Best for ages 8 and upIdeal desde los 8 años

    ElectronicsElectrónica

    Free BYRD, CC BYVirtual tourRecorrido virtual

    Explore everythingExplorar todo